Dell Certified Professional DNDNS-200 certification exam is organized in a systematic way in the DNDNS-200 practice test software so that you cover all the key areas within short time quickly. Dell DNDNS-200 exam dumps simulation makes the learning easier and quicker and facilitates you in customizable learning as well. You can learn how to complete the Dell DNDNS-200 exam in time by managing time according to the DNDNS-200 exam pattern.
♥ VALID DNDNS-200 Exam Questions 2018 ♥
DNDNS-200 exam questions, DNDNS-200 PDF dumps; DNDNS-200 exam dumps:: https://www.dumpsschool.com/DNDNS-200-exam-dumps.html (60 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)
Latest Dell DNDNS-200 Dumps Exam Questions and Answers:
A network engineer needs to remove switch 2 from a stack of four switches permanently.
Which process should the network engineer use?
A. Adjust the stacking cables to take the N-Series switch out of the stack, log into the CLI of the stack, and run the following command:
B. Adjust the stacking cables to take the switch out of the stack. The master switch will automatically remove the switch from the stack.
C. Adjust the stacking cables to take the switch out of the stack, log into the CLI of the stack, and run the following command:
D. Adjust the stacking cables to take the switch out of the stack, and reboot the stack.
http://i.dell.com/sites/doccontent/shared-content/data-sheets/en/Documents/Dell-Networking-N4000-Series-Stacking-Guide.pdf Page: 42
On an S-Series switch, what two events occur when a static null route has been configured in the system to drop a packet? (Choose two.)
A. Null route is installed in the PBR table to drop the packet
B. Null route is saved into the running configuration.
C. Null route is installed in the ACL table with deny statement.
D. Null route is installed in the IP forwarding table.
Dell Networking N-Series N1500, N2000, N3000, and N4000 Switches User’s Configuration Guide. Page: 1009-1010.
Refer to the exhibit.
A network engineer is called onsite to troubleshoot replication failure and traffic loss. Whenever replication occurs between SAN A and SAN B, users report traffic loss between sites, and replication ultimately fails due to traffic loss.
Based on the topology shown, what is the most likely cause of the traffic loss?
A. Traffic needs to be policed on the site border routers.
B. An inbound policy map needs to be defined on the site border that marks the replication traffic with a DSCP value of 46.
C. An outbound policy map needs to be defined on the site border that marks the replication traffic with a DSCP value of 46.
D. Traffic needs to be shaped on the site border routers.
In Quality of Service, DSCP value 46 is high-priority traffic.
Refer to the exhibit of the N-series switches.
The exhibit shows a Layer 2 network between Host A (a Desktop Computer running Windows 7) and Host B (another Desktop Computer running Windows 7) and the list of VLANs Untagged (U) and Tagged (T) at each Ethernet interface: Host A transmits an Ethernet frame untagged on VLAN 1.
What will happen to the Ethernet frame?
A. SW2 drops the Ethernet frame when trying to transmit it out of interface E2 because the incoming and outgoing interfaces are Tagging/Untagging VLAN 1 differently.
B. The Ethernet frame is successfully delivered to Host.
C. STP drops the Ethernet frame because it cannot create an end-to-end loop free path between the switches for VLAN 1.
D. VLAN consistency protocol determines that the VLAN is not correctly Tagged/Untagged on all interfaces, an error will occur, and SW1 will drop the frame on interface E2.
Refer to the exhibit.
Considering the network topology and information shown, what is an issue with end point devices in network 192.168.102.0/24 that try to route to 192.168.101.0/24?
A. ICMP Redirects
B. Suboptimal Routing
C. Routing Loop
D. Summarization Black Hole
Refer to the Exhibit.
A network engineer receives the output shown when removing MLAG from a pair of N-Series switches.
Which sequence of steps must the engineer complete to remove the vpc peer-link from Port Channel 1?
A. Shut down the Port Channel interfaceIssue the no vpc peer-link command on the Port Channel
B. Remove the vpc feature using the no feature vpc commandIssue the no vpc peer-link command on the Port Channel
C. Remove the channel-group command from all members of the Port ChannelIssue the no vpc peer-link command on the Port Channel
D. Remove peer-keepalive enable using the no peer-keepalive enable commandIssue the no vpc peer-link command on the Port Channel
New Updated DNDNS-200 Exam Questions DNDNS-200 PDF dumps DNDNS-200 practice exam dumps: https://www.dumpsschool.com/DNDNS-200-exam-dumps.html