NetApp NS0-180 Exam Questions – Secret To Pass In First Attempt

5 Dec

NetApp Certified Storage Installation Engineer, ONTAP NS0-180 certification exam is organized in a systematic way in the NS0-180 practice test software so that you cover all the key areas within short time quickly. NetApp NS0-180 exam dumps simulation makes the learning easier and quicker and facilitates you in customizable learning as well. You can learn how to complete the NetApp NS0-180 exam in time by managing time according to the NS0-180 exam pattern.

Version: 9.1
Question: 1

You were dispatched to install a cluster made up of FAS8060 and FAS8080 controllers. There are three FAS8060 controllers and three FAS8080 controllers.
Which solution would provide the largest possible cluster?

A. a cluster made up of two nodes
B. a cluster made up of four nodes
C. a cluster made up of five nodes
D. a cluster made up of six nodes

Answer: B

Question: 2

A customer is using a Cisco Nexus 5020 as a cluster network switch.
What would be used as a management network switch in this scenario?

A. Cisco Nexus 5020 1GbE ports
B. Cisco Nexus 5020 Expansion Module
C. Cisco Catalyst 2960
D. Cisco Catalyst 5000

Answer: C

The Cisco Catalyst 2960 switch can be installed as management switch in a NetApp system cabinet.
Clustered Switch Setup Guide for Cisco Switches, page 5

Question: 3

New Updated NS0-180 Exam Questions NS0-180 PDF dumps NS0-180 practice exam dumps: Questions)

What happens to the NTP configuration in clustered Data ONTAP 8.3 when a node joins a cluster?

A. A node that joins a cluster has a separate NTP service.
B. A node that joins a cluster automatically adopts the NTP configuration of the cluster.
C. A node that joins a cluster must be manually configured in the NTP.
D. A node that joins a cluster must reboot before running the NTP service.

Answer: B

A node that joins a cluster automatically adopts the NTP configuration of the cluster.
Reference: How to configure and troubleshoot NTP on clustered Data ONTAP 8.2 and later using CLI

Question: 4

You are assigned to install five DS2246 with twenty-four 400 GB SSDs per shelf to a single node system.
According the NetApp, which statement is correct?

A. You cannot install five SSD shelves to one System.
B. You need at least two stacks.
C. You need at least three stacks.
D. You can put all shelves in one stack.

Answer: D

Up to 10 shelves are supported per stack for the DS2246, so we one stack is enough as we only have five shelves (DS2246s).
Reference: Making the Move from FC to SAS Storage

Question: 5

Which three types of interface groups are supported on NetApp storage systems? (Choose three.)

A. single mode
B. HA interconnect
C. IPspaces
D. static multimode
E. dynamic multimode

Answer: A,D,E

You can create three different types of interface groups on your storage system: single-mode, static multimode, and dynamic multimode interface groups.
Reference: Types of interface groups

Question: 6

You have just configured the customer’s first SVM with a LIF IP The customer’s DNS IP address is and you are unable to ping it from the NetApp storage system, but you are able to ping the gateway and everything else works.
In this scenario what is the problem?

A. You need to have the DNS server on the same subnet as the LIF IP address.
B. You need to add a static gateway to the LIFs routing group.
C. You need to have the customer check the cable.
D. You need to add an IPspace and domain broadcast to the port.

Answer: D

A broadcast domain resides in an IPspace, and it contains a group of network ports, potentially from many nodes in the cluster, that belong to the same layer 2 network. The ports in the group are used in an SVM for data traffic.
Reference: Clustered Data ONTAP 8.3, Network Management Guide, page 8